Safety Guide for the GasAlertQuattro. GasAlertQuattro Alarms. Common Sensor Replacements 1. Sensor Replacement Part Numbers. Applying Gas to the Sensors Part 2. Applying Gas to the Sensors Part 3. Continuing with Auto Spanning and Calibration. A Look at Setting Alarm Setpoints. PID 1. Correction Factor Sheet. Biosystems Software 1. Biosystems BioTrak 9. Changing Oxygen Sensors in the Altair 4X. MSA Product Bulletins Solaris User Manual.
Solaris Quick Reference Guide. Detector Tubes and Pumps Datasheet. Altair 4 QuickCheck Station Datasheet. Explosimeter Datasheet. Explosimeter User Manual. Gascope Datasheet. Gascope User Manual. Tankscope Datasheet. Tankscope User Manual. Altair 4 Datasheet. Altair 4 User Manual. Gas Tester Datasheet. Toximeter II Datasheet. Passport VOC Datasheet. Pulsar CO User Manual. Pulsar H2S User Manual.
Pulsar O2 User Manual. Pulsar Plus Datasheet. Pulsar Plus User Manual. Solaris Fire Datasheet. Titan Datasheet. Titan User Manual. Do not mount the device directly to chiller, piping, or piping supports. Mount the device:. Make sure there is adequate space to connect the external wiring and sample line piping Fig. Make sure the hardware is suitable for the mounting surface and can withstand 70 lb 9 kg without loosening or causing damage to the hardware or mounting surface.
Use all four mounting holes provided on the device Fig. The device can use hard and soft tubing. The following are acceptable tubing types:.
ID Polyurethane tubing ether based. OD Stainless steel tubing. Use the appropriate tools to give a clean, smooth end to the tubing when it is cut. MSA recommends the use of at least two gas-monitoring points per chiller for sufficient detection monitoring. Due to installation and application variations, each system must be analyzed individually. Do a smoke test of the mechanical room to determine the flow pattern and allow for optimal placement of the sample lines.
Keep the total line length of a point, including the sample line and exhaust line, at less than ft m. Keep lines as short as possible to minimize the transport time of the device. Typically, refrigerants collect near the floor. Install the sample points 12—18 in. Failure to use and maintain end-of-line filters can cause inaccurate readings and damage to internal components, and make additional servicing necessary.
Examine and replace the end-of-line filters at regular intervals. The appropriate interval for replacement is determined by the environment of the installation. Install tubing with large enough bend radii to prevent kinking or pinching. Kinking or pinching of the tubing can result in insufficient monitoring of an area. Before connecting tubing to the device, clean all tubing with compressed air or nitrogen to remove debris. These fittings accept the hard and soft tubing specified in Section 4.
Make sure to vent the exhaust of the device to the outside atmosphere preferred or a safe area. Do not use inline or end-of-line filters in the exhaust line. If possible, route the exhaust line so venting occurs to the outside atmosphere.
Make sure to protect the end of the exhaust tube from elements such as water, dirt, snow, ice, and insects, which can cause clogs and prevent efficient venting. Make sure to remove the cap from the exhaust port before operating the device.
Failure to do so will create back pressure that can result in inaccurate readings and damage to internal components. The Chillgard Wiring Diagram Fig. Make sure the device chassis is connected to the earth ground at the ground bar. Failure to follow these warnings can result in serious bodily injury or death. Installations that require conformity to the CE mark must have a connection between the Chillgard device and a nearby earth ground potential.
To achieve this connection, install a 10 AWG or larger copper wire between the grounding lug terminal strip on the right side of the Chillgard device and the grounding point protective earth.
The wire length cannot be longer than 6 ft 2 m. To prevent electrical shock, the circuit board cover must be in place when power is on. Electrical shock can cause serious personal injury or death. Make sure the device is connected directly to the ac power source through a dedicated circuit breaker. Make sure the connectors are seated securely. Each relay can be connected as normally open NO or normally closed NC.
When power is supplied to the device, the green power indicator LED Fig. The loading bar indicates the status of the initializing process. NOTE : An entry for the date is necessary to continue. If this error pop-up shows, select "OK" to return to the previous screen and supply a value. NOTE : A valid entry for the time is necessary to continue.
If password protection is disabled, the "Create Password" and "Verify Password" fields are inactive. NOTE : If password protection is enabled, do the following:. Select to accept the value.
If password protection is enabled, the "Password Required" pop-up will show when any user tries to change an editable screen. Select "Continue" to go to the. Configuration of Point 1 is required for device initialization. The entire 18 characters will only show on the "Point Detail" screen.
Only 10 characters will show on the "Point Configuration" screen. Select "Continue" to go to the gas configuration setup. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?
Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Chillgard Msa Chillgard User Manual Download for 1. Chillgard 3. Chillgard 4. Chillgard 5. Chillgard 6. Warnings and Cautions 2 Warnings and Cautions The Chillgard , hereafter also referred to as "the device", is a gas monitor intended for indoor use in mechanical equipment rooms or commercial spaces where refrigerant equipment, such as centrifugal chillers, is used.
Chillgard 7. Make sure the sample inlet lines to the device are clean and noncondensing. Perform periodic leak tests on all sample lines. Chillgard 8. Description 3 Description The Chillgard provides continuous monitoring of refrigerant gas levels for up to 16 points in nonhazardous areas. Chillgard 9. Description 3. Description 1 2 3 4 Fig. Description 1 3 1 2 4 5 Fig. Sample Line Vdc Vdc 4 or 8 pt system 16 pt system 1 1 1. Installation 4 Installation.
Do not touch the electronic circuit boards. Do not install or operate a device that has damage. Installation 8 Carefully inspect the internal components and assemblies for damage or shortages.
US Fig. Installation 4. Do the following procedure to install end-of-line filters: 1 Remove the new end-of-line filter from the bag. Make sure the arrow on the body of the filter Fig.
0コメント